[Oisf-users] Packet Loss

[Yasha Zislin]

Sorry, forgot to press reply all.
So based on the info I've provided, any more ideas?
Do you need me to upload any more config info?

BTW, if I dont set HTTP.MEMCAP, does that mean it will use unlimited?

Is there a way to find out what kind of traffic is clogging my PF_RING slots?

Thanks again.

> Date: Mon, 9 Jun 2014 16:30:25 +0200
> Subject: Re: [Oisf-users] Packet Loss
> From: petermanev at gmail.com
> To: coolyasha at hotmail.com; oisf-users at lists.openinfosecfoundation.org
> 
> On Mon, Jun 9, 2014 at 4:21 PM, Yasha Zislin <coolyasha at hotmail.com> wrote:
> > So these two interfaces are kind of related. If traffic spikes on one, it
> > will increase on the other.
> > In fact, these two span ports see traffic before and after the firewall. So
> > traffic is the same except for NATting piece. After the firewall IPs change
> > to private addressing.
> > Not sure if this scenario can have issues, BUT my packet drop was occurring
> > when I was just trying to get Suricata to run with one interface.
> > Important point is that CPUs dont hit 100% (it was doing that in the
> > beginning until I started to offload everything to RAM).
> >
> > You are correct about memory consumption of threads. I've increased
> > min_num_slots by running this:
> > modprobe pf_ring transparent_mode=0 min_num_slots=400000 enable_tx_capture=0
> >
> > cat /proc/net/pf_ring/info
> > PF_RING Version          : 6.0.2 ($Revision: exported$)
> > Total rings              : 16
> >
> > Standard (non DNA) Options
> > Ring slots               : 400000
> > Slot version             : 15
> > Capture TX               : No [RX only]
> > IP Defragment            : No
> > Socket Mode              : Standard
> > Transparent mode         : Yes [mode 0]
> > Total plugins            : 0
> > Cluster Fragment Queue   : 3852
> > Cluster Fragment Discard : 428212
> >
> > I could have increased it higher (it let me do that) but Free Num Slots
> > stopped increased after 400000 value.
> > I did notice if I set min_num_slots to default 65k number, Free Num Slots
> > get to 0 faster and packet drop begins.
> >
> > Here is a stat for one of the threads:
> >  cat /proc/net/pf_ring/6224-eth17.595
> > Bound Device(s)    : eth17
> > Active             : 1
> > Breed              : Non-DNA
> > Sampling Rate      : 1
> > Capture Direction  : RX+TX
> > Socket Mode        : RX+TX
> > Appl. Name         : Suricata
> > IP Defragment      : No
> > BPF Filtering      : Disabled
> > # Sw Filt. Rules   : 0
> > # Hw Filt. Rules   : 0
> > Poll Pkt Watermark : 128
> > Num Poll Calls     : 6408432
> > Channel Id Mask    : 0xFFFFFFFF
> > Cluster Id         : 99
> > Slot Version       : 15 [6.0.2]
> > Min Num Slots      : 688290
> > Bucket Len         : 1522
> > Slot Len           : 1560 [bucket+header]
> > Tot Memory         : 1073741824
> > Tot Packets        : 902405618
> > Tot Pkt Lost       : 79757335
> > Tot Insert         : 822648289
> > Tot Read           : 822648236
> > Insert Offset      : 219035272
> > Remove Offset      : 218997656
> > TX: Send Ok        : 0
> > TX: Send Errors    : 0
> > Reflect: Fwd Ok    : 0
> > Reflect: Fwd Errors: 0
> > Num Free Slots     : 688237
> >
> >
> > For NICs I have 10 gig Fiber HP nic (I think with Qlogic chip).
> >
> > BTW, I had to configure both PF_RING interfaces to be the same cluster ID.
> > For some reason, setting them to different numbers would not work.
> >
> > You are correct about the behavior. It runs fine, Free Num Slots for ALL
> > threads get to 0, packet drop starts, after some time Free Num Slots go back
> > to almost 100% available and packet drop stops.
> > It feels like it is getting choked on something and starts to fill up.
> >
> > Timeout values are as follows:
> > flow-timeouts:
> >
> >   default:
> >     new: 3
> >     established: 30
> >     closed: 0
> >     emergency-new: 10
> >     emergency-established: 10
> >     emergency-closed: 0
> >   tcp:
> >     new: 6
> >     established: 100
> >     closed: 12
> >     emergency-new: 1
> >     emergency-established: 5
> >     emergency-closed: 2
> >   udp:
> >     new: 3
> >     established: 30
> >     emergency-new: 3
> >     emergency-established: 10
> >   icmp:
> >     new: 3
> >     established: 30
> >     emergency-new: 1
> >     emergency-established: 10
> >
> > I set them just like one of these "10gig and beyond" articles said.
> >
> > Thank you for your help.
> >
> 
> Thank you for the feedback.
> Please keep the conversation on the list :)
> 
> 
> -- 
> Regards,
> Peter Manev
 		 	   		  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openinfosecfoundation.org/pipermail/oisf-users/attachments/20140609/5bf47dd1/attachment-0002.html>